Station-Drivers - Aquantia AQC107, AQC108, Firmware Version 3.1.56 - STATION-DRIVERS

Aquantia AQC107, AQC108, Firmware Version 3.1.56

Plus d'informations
il y a 8 mois 3 jours - il y a 8 mois 1 jour #1185 par admin


Aquantia AQC107, AQC108 Firmware Version 3.1.56

Nouveau firmware pour les chipsets réseaux Aquantia AQC107, AQC108 Version 3.1.56


AVANT


APRES


Release note:
FW release ver 3.1.56
===========================================================================
FW release bundle for Aquantia NICs (AQC107, AQC108, AQC111, AQC112)

Revision history
3.1.56
Fixes for:
- FW doesn’t report 5G capability to the driver when Autonegis set on both parties
- “Boot to PXE” option doesn’t work on systems with double PERST.
- No link in PXE after image loading was interrupted in PXE with “Ctrl+Alt+Del”

Features:
• Improved transition of PHY to/from low power mode (do not allow other operations while it is in progress)
[AQC111/112] Fixes:
• Disabled PCIe lane auto-disable feature because it cannot work correctly due to switched PCIe lanes in AQC111/112 chip and caused system hang on startup on particular HW
[PCIROM]
• Fixed BSoD due to memory corruption on system start up caused by active datapath: when booting from PXE/UEFI to OS, datapath in the chip remained active and could write to memory while system is booting up. This fix is important for all platforms with enabled OptionROM
• Fixed long start up in PXE when media is not connected (this was caused by attempts to get DHCP address)

3.1.44
Fixes:
- Fixed issue with no link during loopback test
- Fix for pause frame handling in PHY FW
- PHY goes to thermal shutdown at 80 degrees
Features:
• Interface for controlling LEDs from the driver [requested for DPDK]
• Reduced link up time (important for automotive designs)

• Preparations for Host Boot: MAC FW reads BDP from the host after loading

[AQC100] Fixes:
- Fix for long link up at 1G for fiber
• Added SFP+ SMBUS malfunction detector for Felicity board.
• Added SMBus access for the driver [requested for DPDK]
[AQC111/112] Fixes:
• Power optimizations

3.1.32
Fixes:
- Fix for Tx traffic stuck: Force 100M/1G to use XFI/USX for driver mode and use SGMII for sleep proxy mode PTP/AVB: Merged TPO2 feature from 2.x (TPO2 must be enabled from the driver)
- Fix for "Firmware did not check TCP sequence number range in TCP Keepalive"
- Changed the truncation boundary for FW echo responder to 64 bytes (it is a typical echo request size)
- Firmware now ignores packets with bad checksum
- [Bermuda B0] Fix for "Nic is not enumerated with fw when pluged in some PCIe slots"
- [Felicity] Added functionality to disable PFC for AQC100

Features:
- New OptionRom with fixes in PXE
- New PHY Firmware

www.station-drivers.com/index.php?option...3&func=select&id=542

Asrock Z270 Professional, i7 (6700K), 16Go Corsair, SSD960, SSD860/850/840, nVidia GeForce GTX960, Creative SB X-Fi Titanium, Clavier Gskill RVB, Souris Asus Gladius II RGB, Grand tour Enermax Storm, Tapis RGB corsair, Router RT2600 & RT1900, Free Fibre 1Gbs
Pièces jointes :
Dernière édition: il y a 8 mois 1 jour par admin.

Connexion ou Créer un compte pour participer à la conversation.

Plus d'informations
il y a 8 mois 2 jours - il y a 8 mois 2 jours #1188 par rvail
Aquantia 5Gbit network adapter, ran "diag -p" & shows firmware as: 1.5.69.
Following the instructions, ran: "diag -k -f XXXX.clx" (replacing XXXX.clx with DellNormalDirtyWake-3.1.56_bdp.clx) to program the firmware.
Then got:
"PHY flash bdp and clx bdp differ! Specify which to keep if not running in interactive mode. Use --phy_flash_bdp to force flash bdp, or use --phy_clx_bdp to force clx bdp."

Anyone get this firmware flash to work correctly?
Dernière édition: il y a 8 mois 2 jours par rvail.

Connexion ou Créer un compte pour participer à la conversation.

Plus d'informations
il y a 8 mois 2 jours - il y a 8 mois 2 jours #1189 par admin
Me it works perfectly




Asrock Z270 Professional, i7 (6700K), 16Go Corsair, SSD960, SSD860/850/840, nVidia GeForce GTX960, Creative SB X-Fi Titanium, Clavier Gskill RVB, Souris Asus Gladius II RGB, Grand tour Enermax Storm, Tapis RGB corsair, Router RT2600 & RT1900, Free Fibre 1Gbs
Pièces jointes :
Dernière édition: il y a 8 mois 2 jours par admin.

Connexion ou Créer un compte pour participer à la conversation.

Plus d'informations
il y a 8 mois 2 jours #1190 par admin
Voici le test de mes 3 cartes réseaux (Intel I219-V, I211 & Aquantia AQC108)



AQUANTIA AQC108


INTEL I219-V


INTEL I211

Asrock Z270 Professional, i7 (6700K), 16Go Corsair, SSD960, SSD860/850/840, nVidia GeForce GTX960, Creative SB X-Fi Titanium, Clavier Gskill RVB, Souris Asus Gladius II RGB, Grand tour Enermax Storm, Tapis RGB corsair, Router RT2600 & RT1900, Free Fibre 1Gbs
Pièces jointes :

Connexion ou Créer un compte pour participer à la conversation.

Plus d'informations
il y a 8 mois 2 jours #1205 par rvail
@ admin: I'm not doubting that your firmware update was successful. Please refer to my previous reply. The written instructions that were included were followed exactly, yet the flash update was not successful for me. If you did anything different from the provided instructions, then please post.
Thanks in advance.

Connexion ou Créer un compte pour participer à la conversation.

Plus d'informations
il y a 8 mois 2 jours #1206 par admin
ok I had the same answer and so I proceed to update with the command --phy_flash_bdp
I managed to update the firmware as in the picture ;-)

Asrock Z270 Professional, i7 (6700K), 16Go Corsair, SSD960, SSD860/850/840, nVidia GeForce GTX960, Creative SB X-Fi Titanium, Clavier Gskill RVB, Souris Asus Gladius II RGB, Grand tour Enermax Storm, Tapis RGB corsair, Router RT2600 & RT1900, Free Fibre 1Gbs

Connexion ou Créer un compte pour participer à la conversation.

Temps de génération de la page : 0.611 secondes